How to use a washing vacuum cleaner correctly: useful operating tips

There is no housewife who would refuse a vacuum cleaner with a wet cleaning function.This is a very convenient technique that provides really high-quality and fast cleaning of various surfaces.

It will be useful for those who own such a device to learn how to use a washing vacuum cleaner in order to achieve maximum efficiency of its operation and extend the life of the home assistant. The information presented in the article will also be useful to those who are just thinking about purchasing a multifunctional unit.

The principle of operation of the washing “cleaner”

The algorithm for carrying out standard cleaning is known. First, the housewife collects dust and debris with a regular vacuum cleaner, then arms herself with a bucket of water and a rag to wash the floor. If the house has a washing vacuum cleaner, these two stages can be performed simultaneously.

The unit sucks up dust and small debris. After this, it delivers a stream of clean water to the floor surface, which it immediately absorbs and disposes of in a separate container. As a result, cleaning time is reduced, and its quality, according to reviews, is significantly improved.

A good washing vacuum cleaner is accompanied by detailed instructions that need to be studied, as well as a set of documents that confirm the quality of the device

Some models of washing vacuum cleaners make it possible to spray water in separate streams. This is useful where you need to deal with complex contaminants.

A great addition is the steam function. Such a unit is more expensive, but helps to cope with even the most complex contaminants.

Attachments designed for processing various surfaces improve the quality of cleaning with a washing vacuum cleaner. Often there is a compartment in the device body for storing them.

Inside the washing vacuum cleaner there are two reservoirs: with clean and dirty water. Before you start cleaning, the first one needs to be filled, and the second one should be clean and dry by this time. The device is serviced immediately after each cleaning cycle.

The cleaning liquid enters through the spray capillary and is almost immediately sucked into the main pipe and then transferred to the dirty water compartment

When purchasing a vacuum cleaner, you should pay attention to the volume and position of the tanks. The optimal size of the container should allow you to completely treat the entire floor area without the need to add clean water to the device.

The location of the containers depends on the model and can be different:

• next to each other;
• one above the other;
• a tank inside another tank.

It is important to understand which container, “clean” or “dirty,” is removed first when servicing the unit. It is more convenient to start cleaning it after cleaning if you can first remove the tank with dirty water.

If, due to the large area or modest size of the model, you need to add clean water, it is better to take a model with access to a “clean” container. Most often, manufacturers use the last option, a tank in a tank, as it is considered the most convenient.

The vacuum cleaner usually comes with the necessary chemicals for wet cleaning: concentrated shampoo and defoamer, although low-foam formulations are also available on sale. When using them, you will not need a foam damper

Also involved in the cleaning process detergent, which must be dissolved in clean water. Mixing is usually done in a separate container and then poured into an appropriate container. The solution is supplied through a special capillary tube. It is usually located along the hose and suction pipe, inside or outside.

TOMAS vacuum cleaners are equipped with a special water box, which is used as a water filter during dry cleaning, and is designed to collect dirty water during wet cleaning.

Most often, the spray hose is located outside and is fixed on the surface of the telescopic tube with special clips. This design is typical for models that are designed for both dry and wet cleaning. When the spray elements are not needed, they can simply be removed.

During the cleaning process, the cleaning composition is sprayed onto the floor in front of the cleaning nozzle, then washed off with water, which is sucked up by the main pipe. Good suction power is the most important characteristic of a washing vacuum cleaner. There are models with and without filters; the principles of caring for such devices differ markedly.

If the washing vacuum cleaner has several filter elements, after each cleaning they need to be removed, washed and dried, and periodically replaced with new ones.

Modern HEPA filters are good at keeping even fine dust inside, but they need constant cleaning and periodic replacement.

If a worn filter is not replaced in time, the suction performance of the vacuum cleaner will deteriorate and the overall quality of cleaning will decrease. Models that do not have filters do not have this problem.

Preparing the device for operation

Before you start cleaning, you need to prepare the washing vacuum cleaner. The procedure for using a specific model is usually described in detail in the instructions.

In general, you need to follow a number of simple steps:

1. Fill the “clean” reservoir with water or cleaning solution.
2. Attach the capillary tube to the spray nozzle and to the connector on the body.
3. Connect the capillary to the suction pipe with special clips.
4. Connect the suction pipe to the hose.
5. Insert the hose into the connector provided for it.
6. Pull out the cable and connect the vacuum cleaner to the power supply.

If the model is equipped with filter elements, then you should add defoamer for vacuum cleaner. Of course, before starting work, all filters must first be cleaned, dried and installed in their designated places.

A washing vacuum cleaner consists of many components that need to be connected correctly. Before each cleaning, check the integrity of the power cable and the tightness of the telescopic tube

Although the vacuum cleaner is called a detergent, it can also be used for dry cleaning. In this case, there is no need to pour water and detergent into the reservoir. This mode will be appropriate for cleaning upholstered furniture, carpets and other surfaces that absorb water.

A particularly high degree of cleaning is provided by washing vacuum cleaners equipped with a steaming function, but it should be remembered that not all coatings tolerate contact with hot steam well.

You should not rely on your own intuitive understanding; before using the washing vacuum cleaner for the first time, you should definitely study the instructions compiled by the manufacturer. If the appliance has not been used for a long time, it is also recommended to refresh your knowledge regarding its correct use.

Actions after cleaning is completed

The floor is cleaned and washed, it's time to tidy up the washing vacuum cleaner.

Procedure:

1. Disconnect the device from the power supply.
2. Place the cord in the socket provided for it.
3. Remove the container with dirty water.
4. Pour out the water and wash the tank.
5. Rinse nozzles and hoses.
6. Dry all washed items.
7. Clean and dry filters and baffles.
8. Remove any remaining water from the “clean” tank and dry it.

Only after all parts have dried can you assemble the vacuum cleaner and store it. Separately, it is worth mentioning the care of filters. All filter elements must be removed, washed and dried thoroughly. Only after this can the filters be installed in place.

The HEPA filter needs regular and proper cleaning. It provides air filtration, retaining even very fine fractions of contaminants

If you collect a vacuum cleaner while the elements are even slightly damp, mold and mildew will appear on them, and this is dangerous for the health of the residents of the house. In addition, you need to regularly replace the filters with new ones, since even with regular and thorough cleaning, they gradually become clogged and become ineffective.

The lifespan of a conventional HEPA filter is usually designed for thirty hours of active use. This time is usually completed in six months or less, depending on the intensity of use of the washing vacuum cleaner. In terms of dust protection, separator-type models without filters are considered more effective.

You should not use a damp or damaged filter, as harmful substances, such as mold, mildew, etc., may enter the air.

They are especially recommended where people with severe allergic reactions live. The special design of such devices allows you to retain even the smallest particles of dust.

The built-in turbine creates a high-pressure area inside the housing, which helps move all contaminants, including allergens, directly into the dirty water tank.

There is no need to add defoamers to such a vacuum cleaner, and its maintenance is a little easier, since there is no need to clean and replace filters. It should be remembered that a high-quality filterless vacuum cleaner must have, among other documents, an air purification certificate.

Example of using Karcher Puzzi

Karcher is one of the most famous manufacturers of cleaning equipment. How to use industrial vacuum cleaner Karcher Puzzi will help you get a more accurate understanding of the use of these complex units.

Before starting work, the manufacturer recommends checking the condition of the power cable and suction hose each time.

After this, the following elements are connected in series:

• nozzle - fixed with a union nut;
• suction pipe;
• elbow - fixed with a union nut;
• suction hose;
• spray hose.

The collected elements are connected to a washing vacuum cleaner. In this case, the suction hose is first inserted into the socket on the body, and then the connection between this element and the spray hose is made with the elbow. Particular attention should be paid to the junction of the spray hose with the elbow; a special coupling is designed for this.

In a separate container, you need to mix the detergent composition and clean water in the proportions that are recommended for this particular product. It is better to use warm water (no more than 50°C) to increase cleaning efficiency. In this case, you need to make sure that the coating can withstand contact with warm liquid without damaging its condition.

If you intend to clean delicate surfaces (colored carpet, upholstery), you first need to test the detergent composition and the temperature of the working fluid in an inconspicuous area

The prepared solution is poured into a “clean” container up to the MAX mark. Now you can connect the vacuum cleaner to the power supply. Then press the SUCTION and SPRAY knobs to begin the cleaning procedure.

First, it is recommended to check the resistance of the coating to moisture and cleaner in some inconspicuous place. If the color and texture of the carpet remain unchanged, cleaning can continue. To supply the cleaning solution to the surface, a special lever is provided on the elbow of the washing vacuum cleaner.

The nozzle is moved along the floor covering in such a way that “paths” are formed with a slight overlap. The nozzle cannot be moved in any direction; only reverse motion is used. For periods when direct cleaning needs to be suspended, the nozzle can be hidden in the slot provided for this purpose on the handle.

After the coating has been treated with the solution, you can go over it again without splashing, as with dry cleaning. This will speed up the drying of the surface. When working with areas where there is heavy contamination, it is recommended to spray the composition and pause for about a quarter of an hour.

Before you start cleaning, you need to pour clean water with shampoo dissolved in it into the appropriate container. The concentration and method of dilution depends on the type of product and is indicated in the instructions for it

A short break ensures contact of the composition with dirt and increases cleaning efficiency.After this, you need to treat the surface again as during normal cleaning, and then again, but using only clean water.

When working with chemical-sensitive surfaces (multi-colored carpets, upholstery), you can reduce the concentration of the special product.

Particular care should be taken when working with jute surfaces, which are prone to color loss and deformation when in contact with moisture. For high-pile carpets, after cleaning, additional treatment with a brush or broom in the direction of the pile is recommended. This must be done before the surface dries.

When the cleaning process is completed, first move the SUCTION and SPRAYING handles to their original position, after which the vacuum cleaner can be unplugged. Now it is important to correctly carry out the maintenance procedure for the device. First, empty the “dirty” tank.

To do this, open the housing lid, take out the container and pour the waste water out of it. Do the same if this tank overflows during cleaning. First, of course, you need to unplug the vacuum cleaner and turn the switches.

Then you need to remove and empty the container, put it in place and perform the reverse operations: turn on the device and move the SUCTION and SPRAYING handles to the working position. At the end of cleaning, the compartment is washed with running water.

Now you should empty the “clean” container of any remaining liquid.

They do it like this:

• disconnect the vacuum cleaner from the network;
• relieve pressure inside; for this purpose, there is a lever located on the knee;
• disconnect the spray hose;
• lower the main hose into a container of water;
• turn on the vacuum cleaner and move the SUCTION handle;
• wait until the device pumps the liquid out of the container.

The next stage is washing the working elements of the device. The elbow is connected to the main hose and capillary. Now approximately two liters of ordinary clean water are poured into a “clean” container. There is no need to use a cleaning compound here.

Now you need to turn on the spray SPRAY. The washing process takes one or two minutes. Then the vacuum cleaner should be turned off. Once both tanks are cleaned, they need to be dried. The outside of the housing is wiped with a damp cloth, and its lid is left in the open position while drying.

If servicing a washing vacuum cleaner seems too difficult, you can choose a different type of unit. Good cleaning quality is demonstrated models with aqua filter.

Conclusions and useful video on the topic

Visual video instructions for using the THOMAS washing vacuum cleaner:

Review of the industrial model Karcher Puzzi 10/1:

Assembly process of the ZELMER 7920.5 vacuum cleaner with filters:

The advertisement claims that using the washing vacuum cleaner is easy and simple. But in reality, maintaining this expensive unit will require some time and effort. However, all costs will pay off, since the quality of cleaning will increase significantly.

Do you have anything to add, or do you have questions about the operation and maintenance of washing vacuum cleaners? You can leave comments on the publication, participate in discussions and share your own experience of using such units. The contact form is located in the lower block.